Replacement Refrigerator Water Filter For:
PUR T1KB1
Filter Features
-
Filter Life: 6-Months
-
Filter Capacity: 200 Gallon
-
NSF Certified 42 & 53
-
Taste
-
Odor
-
Chlorine
-
Reduces 24 Contaminants Including Pharmaceuticals
-
Replacement Refrigerator Water Filter For:
T1KB1
2-Pack ($35.99)
Save:
$34.00
158 Review
Add To Cart
-
Replacement Refrigerator Water Filter For:
T1KB1
3-Pack ($52.99)
Save:
$47.00
237 Review
Add To Cart
-
Replacement Refrigerator Water Filter For:
T1KB1
4-Pack ($69.99)
Save:
$60.00
95 Review
Add To Cart
-
Replacement Refrigerator Water Filter For:
T1KB1
6-Pack ($102.99)
Save:
$27.00
69 Review
Add To Cart
Remove unhealthy contaminants and any haziness efficiently from your drinking water with PUR T1KB1 at Clatterans which uses the highest quality activated carbon and certifies to IAPMO, NSF/ANSI water treatment standards 42 for trapping and reducing detrimental impurities to reach the best water filtration results. We have numerous PUR refrigerator filter replacements to fit perfectly in your fridge. Fitermodel is an acceptable substitute without compromise on quality and flow to provide wholesome sweet water for your whole family. Drink safe water and taste clean ice from Clatterans filters.
Fits The Following Series
45429 Series |
45433 Series |
58703 Series |
51103 Series |
51102 Series |
1.Press the eject button to release the filter from the base grille.
2.Pull the filter straight out.
3.Turn the cap counterclockwise to remove it from the filter.
IMPORTANT: Do not discard the cap. It is part of your
refrigerator. Keep the cap to use with the replacement filter.
4.Align the ridge on the cap with the arrow on the new filter and turn the cap until it snaps into place.
NOTE: You can run the dispenser without a filter. Your water will not be filtered. Simply insert the cap all of the way into the base grille and rotate the cap until it is firmly in place.
5.Remove the protective covers from the O-rings. Be sure the O-rings are still in place after the covers are removed.
6.Push the filter into the base grille. The eject button will pop back out when the filter is fully engaged.
7.Run water from the dispenser for 5 minutes at .5 gpm (about 2½ gallons) to clear the system and prevent sputtering.
NOTE: Initial rate may be slower than expected. Full rate should be restored within 24-36 hours
8.Reset the “replace filter” light, if needed, by holding the reset button for three seconds.
Top customer reviews
-
By Ronnie On 2018-01-23 02:48:08
At first the water tastes a little off, but after a few times it begins delivering the tasting water. Therefore, I'm only giving it 4 stars to wait Clatterans upgrade their filters.
-
By Rex On 2018-01-22 05:14:18
This was the first filter change for our new refrigerator. Used the official filter based on feedback that cheaper versions leaked and caused problems. Also liked the fact that this one removes so many contaminates. This worked great and was easy to change, and the water is great.
-
By Jamie On 2018-01-21 13:00:38
Replaced a fridge filter which had been sitting in the fridge for a long time, the in-door water was not tasting good. This filter, whirlpool filter 3, fit into my fridge exactly as described, followed the directions as outlined on the package and in the fridge's owners manual and had clear, great tasting filtered water when all was said and done. Great to be able to get filtered water from the fridge rather than waiting for the Whirlpool pitcher to fill up!
-
By Johnnie On 2018-01-21 04:05:00
I went out on a limb in ordering this product. I could not find the water filter for my kenmore refrigerator. I used the model number - Kenmore 9030 filter, and this filter came up on my search. The thing is, I had never changed the filter before. I had no idea what too look for. I ordered it. I watched a video on how to change the filter. Once, the filter arrived, I followed the instructions on the video. And, it worked. I flushed the system, and almost immediately, clear clean water flowed from the refrigerator. I am very happy.
-
By Taylor On 2018-01-19 08:40:55
These filters are so much more economical than the name brand and they work exactly the same. They have a snug fit. I had the water tested and it was just as good as the water filtered by the name brand filters.
-
By Bernice On 2018-01-17 00:58:12
Fits like a glove. If you go to the Clatterans website, they show you all the additional pollutants this filter catches. It is much cheaper than the original filter and has better packaging, but the way I see it, it provides a lot more protection for my family and I against the stuff in our municipal water supplies.
How often should you replace your water filter?
- On average, most filters last 6 months or 300 gallons depending on your water quality and usage.
How do I turn off my filter light to reset?
- If the filter light will not reset after following specific instructions from your owner manual, contact your refrigerator manufacturer.
Do the gaskets (o-rings) on the filters need to be lubricated?
- Most water filters come with pre-lubricated O-rings
- If you are having trouble installing the filter, we have found that a small amount of vegetable oil applied to the O-ring will ease installation and removal of the filter.
I just installed my filter; do I need to run water through it before I drink the water? If so, how much?
- You should run 3 gallons of water through your filter in order to flush it and make sure that it is thoroughly wet. Do not run the 3 gallons continuously, instead run the water for a few minutes and stop in between. Get a gallon water container, and pour and refill 3 times!
Live Customer Support
Our hours of operation are Monday thru Friday from 8:00am to 6:00pm Eastern Time and our after hours sales team is available 24 hours a day, 7 days a week. Whether it’s placing an order or answering questions that may help in your purchasing decisions, our specialists are ready to assist you. You can also contact us via email.