Replacement Refrigerator Water Filter For:
Kenmore 469081
Filter Features
-
IAPMO Certified and meets NSF/ANSI standards 42
-
Remove chlorine, lead, mercury, cadmium, and thallium
-
Six months water filter service life
-
Easy and fast filter replacement
-
Replacement Refrigerator Water Filter For:
469081
2-Pack ($35.99)
Save:
$34.00
160 Review
Add To Cart
-
Replacement Refrigerator Water Filter For:
469081
3-Pack ($52.99)
Save:
$47.00
224 Review
Add To Cart
-
Replacement Refrigerator Water Filter For:
469081
4-Pack ($69.99)
Save:
$60.00
85 Review
Add To Cart
-
Replacement Refrigerator Water Filter For:
469081
6-Pack ($102.99)
Save:
$27.00
97 Review
Add To Cart
Elevate the life quality starting from drinking water in your Kenmore refrigerator by changing the 469081 at Clatterans where stores a huge inventory of Kenmore filters to clear up hazardous components like mercury, thallium and terrible contaminants which do harm to our health. Certified by IAPMO and tested by NSF/ANSI standard 42, Clatterans 469081 will reduce parasites, pesticides and other pharmaceutical pollutants. Take more out of your water by replacing your Kenmore refrigerator filter every six months to drink natural filtered water and ice in the next days.
Fits The Following Series
50023 Series
50022 Series
41169 Series
51123 Series
50029 Series
1. Locate the water filter in the top-right corner of the refrigerator compartment and open the cover door. The filter will be released and then be ejected as the door is opened.
2. When the door is completely open, pull the filter straight out.
NOTE: There may be some water in the filter. Some spilling may occur. Use a towel to wipe up any spills.
3. Take the new filter out of its packaging and remove the covers from the O-rings. Be sure the O-rings are still in place after the covers are removed.
4. With the arrow pointing to the left (toward the filter cover door’s hinge), align the new filter with the filter housing and slide it into place. The filter cover door will automatically begin to close as the new filter is inserted.
5. Close the filter cover door completely in order to snap the filter into place. You may need to press hard.
6. Run water from the dispenser for 5 minutes at .5 gpm (about 2½ gallons) to clear the system and prevent sputtering.
NOTE: Initial rate may be slower than expected. Full rate should be restored within 24-36 hour
7. Reset the “replace filter” light, if needed, by holding the reset button for three seconds.
Top customer reviews
-
By Kristin On 2020-01-06 03:44:10
Would buy it again and will have to in another 6 months. The Clatterans water filter replacement, no muss no fuss. Was 15.00 less than local hardware store.
-
By Gregg On 2020-01-04 11:14:19
The filters are just right for my Kenmore fridge, I have ordered these before and will do again.
-
By Geneva On 2020-01-01 23:18:58
Just replaced the PUR filter with this Clatterans replacement and our water tastes like water again! For the past year since we purchased a new refrigerator the water straight from the sink has tasted better than the water that has been filtered in the fridge. Some days it was fine, other days it would taste off. We replaced filters every 2-4 months, much more frequently than we should need to. I've only installed this new filter today so I'm not sure what it will be like in the long term, but I am very happy to report the water tastes wonderful again!
-
By Susie On 2020-01-01 06:33:12
We bought this to replace the water filter - A little bit expensive for our family as we need to change it every three months - Works - no issues with installation or "POP" out - like previous reported
-
By Thomas On 2019-12-31 23:43:33
We have been using it for almost a month and no complaints. We did have to pour a lot of water when we first installed it because it was coming out in a weird color. Then I asked the customer service, just know this is a normal situation.
-
By Roderick On 2019-12-31 04:56:15
Expensive, but worth it for me to buy the factory original part...I read reviews on the less expensive ones about them leaking, and there's no way I wanted to take that chance with our new laminate hardwood floors!
How often should you replace your water filter?
- On average, most filters last 6 months or 300 gallons depending on your water quality and usage.
How do I turn off my filter light to reset?
- If the filter light will not reset after following specific instructions from your owner manual, contact your refrigerator manufacturer.
Do the gaskets (o-rings) on the filters need to be lubricated?
- Most water filters come with pre-lubricated O-rings
- If you are having trouble installing the filter, we have found that a small amount of vegetable oil applied to the O-ring will ease installation and removal of the filter.
I just installed my filter; do I need to run water through it before I drink the water? If so, how much?
- You should run 3 gallons of water through your filter in order to flush it and make sure that it is thoroughly wet. Do not run the 3 gallons continuously, instead run the water for a few minutes and stop in between. Get a gallon water container, and pour and refill 3 times!
Live Customer Support
Our hours of operation are Monday thru Friday from 8:00am to 6:00pm Eastern Time and our after hours sales team is available 24 hours a day, 7 days a week. Whether it’s placing an order or answering questions that may help in your purchasing decisions, our specialists are ready to assist you. You can also contact us via email.