Whirlpool WRF989SDAE
Fits The Following Models
Whirlpool Refrigerator Models
-
WRF989SDAB02
-
WRF989SDAB01
-
WRF989SDAB00
-
WRF989SDAB
-
WRF560SMYW00X
-
WRF560SMYM00
-
WRF560SMYH02
-
WRF560SMYH01
-
WRF560SMYH00
-
WRF560SMYE02
-
WRF560SMYE01
-
WRF560SMYE00
-
WRF560SMYB00
-
WRF560SFYW00
-
WRF560SFYM00
-
WRF560SFYE00
-
WRF560SFYB00
-
WRF560SEYW00
-
WRF560SEYM00
-
WRF560SEYB00
-
WRF989SDAB03
-
WRF989SDAE
-
WRF989SDAE00
-
WRF989SDAF
-
WRF989SDAF00
-
WRF989SDAH
-
WRF989SDAH00
-
WRF989SDAM
-
WRF989SDAM00
-
WRF989SDAW
-
WRF989SDAW00
-
WRF989SDAW00
-
WRF989SDAW
-
WRF989SDAM00
-
WRF989SDAM
-
WRF989SDAH00
-
WRF989SDAF00
-
WRF989SDAF
-
WRF989SDAE00
-
WRF989SDAE
-
WRF989SDAB03
-
WRF989SDAB02
-
WRF989SDAB01
-
WRF989SDAB00
-
WRF989SDAB
-
WRF560SMYW00X
-
WRF560SMYM00
-
WRF560SMYH01
-
WRF560SMYE02
-
WRF560SMYE01
-
WRF560SMYE00
-
WRF560SMYB00
-
WRF560SFYW00
-
WRF560SFYM00
-
WRF560SFYE00
-
WRF560SFYB00
-
WRF560SEYW00
-
WRF560SEYM00
-
WRF560SEYB00
-
WRF989SDAH
-
WRF560SMYH00
-
WRF560SMYH02
1. Locate the accessory packet in the refrigerator and remove the water filter.
2. Take the water filter out of its packaging and remove the cover from the 0-rings. Be sure the 0-rings are still in place after the cover is removed.
NOTE: There may be some water in the filter. Some spilling may occur. Use a towel to wipe up any spills.
3. Align the arrow on the water filter label with the cutout notch in the filter housing and insert the filter into the housing.
4. Turn the filter clockwise until it locks into the housing.
NOTE: If the filter is not correctly locked into the housing, the water dispenser will not operate. Water will not flow from the dispenser.
5. While the compartment door is still open, lift the filter up into the compartment Then, close the filte compartment doo completely.
6. Run water from the dispenser for 5 minutes at .5 gp(about 2.5 gallons) to clear the system and preven sputtering.
NOTE: Initial rate may be slower than expected. Full rate should be restored within 24-36 hours.
7. Reset the "replace filter" light, if needed, by holding the reset button for three seconds.
Top customer reviews
-
By Bobbie On 2020-01-28 13:16:18
Make sure to read the instructions!! Must purge filter with 3 Gallons of water immediately or you get a strange, stick-like substance in your water. I learned this the hard way.
-
By Tanya On 2020-01-22 04:23:02
Installation is straight forward. Be sure to follow instructions and run through the recommended amount of water.
-
By May On 2020-01-20 09:24:33
Great filter for my fridge to keep my water and ice nice and crisp. The best price is on Clatterans. Will definitely come back here for my next filter.
-
By Heather On 2020-01-17 09:01:27
This is exactly what was in the refrigerator when I purchased it. It lasted one year before I had to replace it.
-
By Brad On 2020-01-14 14:30:18
Needed, but not as long-lasting as expected. This isn't just a problem with Clatterans, for the original filters didn't last as long as the manual said either. It would be great if they were less expensive.
-
By Donnie On 2020-01-10 04:56:15
You have to flush the filter with 3 gallons of water at install before you take your first drink. My fridge (model WRX988SIBM03) deducts these "primed" gallons from the filter capacity/used percentage. I think after the initial flush I saw it was at 97%. It cuts into the replacement timer, making it sooner I need to replace it. The water is a little cloudy after the initial flush but goes away after a few seconds. I don't get a milky color as some report. I don't have an issue with taste. We are fortunate to live in a city with great tasting and clean water so if I don't replace the filter once the indicator light comes on, not a big deal. No one is going to die. No issue with water pressure, streaming, spitting, etc. Been using these filters for almost 2 years now. 4 stars because they are expensive.
Common Water Filter Questions
How often should you replace your water filter?
- On average, most filters last 6 months or 300 gallons depending on your water quality and usage.
How do I turn off my filter light to reset?
- If the filter light will not reset after following specific instructions from your owner manual, contact your refrigerator manufacturer.
Do the gaskets (o-rings) on the filters need to be lubricated?
- Most water filters come with pre-lubricated O-rings
- If you are having trouble installing the filter, we have found that a small amount of vegetable oil applied to the O-ring will ease installation and removal of the filter.
I just installed my filter; do I need to run water through it before I drink the water? If so, how much?
- You should run 3 gallons of water through your filter in order to flush it and make sure that it is thoroughly wet. Do not run the 3 gallons continuously, instead run the water for a few minutes and stop in between. Get a gallon water container, and pour and refill 3 times!