Whirlpool WRF989SDAW00
Fits The Following Models
Whirlpool Refrigerator Models
-
WRF989SDAB02
-
WRF989SDAB01
-
WRF989SDAB00
-
WRF989SDAB
-
WRF560SMYW00X
-
WRF560SMYM00
-
WRF560SMYH02
-
WRF560SMYH01
-
WRF560SMYH00
-
WRF560SMYE02
-
WRF560SMYE01
-
WRF560SMYE00
-
WRF560SMYB00
-
WRF560SFYW00
-
WRF560SFYM00
-
WRF560SFYE00
-
WRF560SFYB00
-
WRF560SEYW00
-
WRF560SEYM00
-
WRF560SEYB00
-
WRF989SDAB03
-
WRF989SDAE
-
WRF989SDAE00
-
WRF989SDAF
-
WRF989SDAF00
-
WRF989SDAH
-
WRF989SDAH00
-
WRF989SDAM
-
WRF989SDAM00
-
WRF989SDAW
-
WRF989SDAW00
-
WRF989SDAW00
-
WRF989SDAW
-
WRF989SDAM00
-
WRF989SDAM
-
WRF989SDAH00
-
WRF989SDAF00
-
WRF989SDAF
-
WRF989SDAE00
-
WRF989SDAE
-
WRF989SDAB03
-
WRF989SDAB02
-
WRF989SDAB01
-
WRF989SDAB00
-
WRF989SDAB
-
WRF560SMYW00X
-
WRF560SMYM00
-
WRF560SMYH01
-
WRF560SMYE02
-
WRF560SMYE01
-
WRF560SMYE00
-
WRF560SMYB00
-
WRF560SFYW00
-
WRF560SFYM00
-
WRF560SFYE00
-
WRF560SFYB00
-
WRF560SEYW00
-
WRF560SEYM00
-
WRF560SEYB00
-
WRF989SDAH
-
WRF560SMYH00
-
WRF560SMYH02
1. Locate the accessory packet in the refrigerator and remove the water filter.
2. Take the water filter out of its packaging and remove the cover from the 0-rings. Be sure the 0-rings are still in place after the cover is removed.
NOTE: There may be some water in the filter. Some spilling may occur. Use a towel to wipe up any spills.
3. Align the arrow on the water filter label with the cutout notch in the filter housing and insert the filter into the housing.
4. Turn the filter clockwise until it locks into the housing.
NOTE: If the filter is not correctly locked into the housing, the water dispenser will not operate. Water will not flow from the dispenser.
5. While the compartment door is still open, lift the filter up into the compartment Then, close the filte compartment doo completely.
6. Run water from the dispenser for 5 minutes at .5 gp(about 2.5 gallons) to clear the system and preven sputtering.
NOTE: Initial rate may be slower than expected. Full rate should be restored within 24-36 hours.
7. Reset the "replace filter" light, if needed, by holding the reset button for three seconds.
Top customer reviews
-
By Wilson On 2020-01-09 02:16:26
I read a lot of reviews about this before buying it and was a little concerned. It was the cheapest I could find though so I went with it. I flushed it out as the instructions stated and the water has been great. I'm not sure if the fridge makes new noises or they're just noises that I didn't notice before. I've had this in for about 4 months now and plan to purchase again when need be.
-
By Douglas On 2020-01-07 03:13:10
Why pay prices for an authentic piece? It's a filter for heaven's sake. Save money & buy these, they work just the same. It's like buying parts for your car. Some people spend the extra money on genuine parts, ok if you want to.
-
By Katie On 2020-01-05 09:31:21
Same as what came with the refrigerator. We go through such ice and water that I have to change ours about every two months. Yes: You do have to run about 2 to 3 gallons of water after changing filters to get good, clear water.
-
By Gwen On 2020-01-04 10:16:58
I did a bad thing. I purchased this filter then read the reviews. Only the negative ones. I thought my goodness what have I done? I was going to send it right back. On a chance, I read a positive review that somewhat explained what most negatives were having and how to correct the issue per the instructions on the filter.
So my big moment arrives and I pull out the filter my Jenn-Air came with from the factory. I just started to laugh as it was the exact same filter I had in my fridge for over 6 months with zero problems.
-
By Steve foster On 2020-01-03 08:33:05
Received new refrigerator filters today, fast shipping, perfect fit and no dirty smelling water all at a great price.
-
By Vera On 2020-01-03 06:45:16
Must flush with at least 3 gallons of water before use. Water comes out clear and tastes great.
Common Water Filter Questions
How often should you replace your water filter?
- On average, most filters last 6 months or 300 gallons depending on your water quality and usage.
How do I turn off my filter light to reset?
- If the filter light will not reset after following specific instructions from your owner manual, contact your refrigerator manufacturer.
Do the gaskets (o-rings) on the filters need to be lubricated?
- Most water filters come with pre-lubricated O-rings
- If you are having trouble installing the filter, we have found that a small amount of vegetable oil applied to the O-ring will ease installation and removal of the filter.
I just installed my filter; do I need to run water through it before I drink the water? If so, how much?
- You should run 3 gallons of water through your filter in order to flush it and make sure that it is thoroughly wet. Do not run the 3 gallons continuously, instead run the water for a few minutes and stop in between. Get a gallon water container, and pour and refill 3 times!