Replacement Refrigerator Water Filter For:
Maytag 46 9020
Filter Features
-
Filter Life: 6-Months
-
Filter Capacity: 200 Gallon
-
NSF Certified 42 & 53
-
Taste
-
Odor
-
Chlorine
-
Reduces 24 Contaminants Including Pharmaceuticals
-
Replacement Refrigerator Water Filter For:
46 9020
2-Pack ($35.99)
Save:
$34.00
158 Review
Add To Cart
-
Replacement Refrigerator Water Filter For:
46 9020
3-Pack ($52.99)
Save:
$47.00
231 Review
Add To Cart
-
Replacement Refrigerator Water Filter For:
46 9020
4-Pack ($69.99)
Save:
$60.00
95 Review
Add To Cart
-
Replacement Refrigerator Water Filter For:
46 9020
6-Pack ($102.99)
Save:
$27.00
69 Review
Add To Cart
Remove unhealthy contaminants and any haziness efficiently from your drinking water with maytag 46 9020 at Clatterans which uses the highest quality activated carbon and certifies to IAPMO, NSF/ANSI water treatment standards 42 for trapping and reducing detrimental impurities to reach the best water filtration results. We have numerous maytag refrigerator filter replacements to fit perfectly in your fridge. Fitermodel is an acceptable substitute without compromise on quality and flow to provide wholesome sweet water for your whole family. Drink safe water and taste clean ice from Clatterans filters.
Fits The Following Series
45429 Series |
45433 Series |
58703 Series |
51103 Series |
51102 Series |
1.Press the eject button to release the filter from the base grille.
2.Pull the filter straight out.
3.Turn the cap counterclockwise to remove it from the filter.
IMPORTANT: Do not discard the cap. It is part of your
refrigerator. Keep the cap to use with the replacement filter.
4.Align the ridge on the cap with the arrow on the new filter and turn the cap until it snaps into place.
NOTE: You can run the dispenser without a filter. Your water will not be filtered. Simply insert the cap all of the way into the base grille and rotate the cap until it is firmly in place.
5.Remove the protective covers from the O-rings. Be sure the O-rings are still in place after the covers are removed.
6.Push the filter into the base grille. The eject button will pop back out when the filter is fully engaged.
7.Run water from the dispenser for 5 minutes at .5 gpm (about 2½ gallons) to clear the system and prevent sputtering.
NOTE: Initial rate may be slower than expected. Full rate should be restored within 24-36 hours
8.Reset the “replace filter” light, if needed, by holding the reset button for three seconds.
Top customer reviews
-
By Keller On 2018-02-26 01:16:18
This is the best Whirlpool filter I have used in our refrigerators. I used to buy water filters at Sears for replacement and if the water sat out for a few hours it would taste bad again. This water tastes so clean and stays that way, even overnight. Some reviews seem dissapointed with the fact that they opened the filter and it's just charcoal inside a cloth. That's all a water filter is! But whatever is different about the quality of this filter is well with the price.
-
By Irvin On 2018-02-24 09:19:18
exactly as promised. The description for Kenmore 9030 said though that some damage of the outer package of could be seen, but I really couldn't see anything I would call damage. The filter was securily packaged and works fine.
-
By Gabriel On 2018-02-24 08:08:06
I installed the filter after receiving it yesterday. And flushed it with 2 large pitchers of water ... no leaks ... no restricted flow ... no issues at all. Then I tentatively sipped the first cup of water expecting plastic tastes ... guess what? water ... plain and simple. No after taste, no discoloration ... just water ... the new filters are just fine folks ... just like the old ones
-
By Doug On 2018-02-23 04:17:18
Finding a replacement Kenmore water filter for our fridge is getting harder. This one works awesome. Hopefully it will be available when it's time to replace again.
-
By Johnnie On 2018-02-21 05:07:03
Easy to install, taste is fine. I tried some cheaper brands, had a funny
taste. Went back to this PUR W10121145. Paid a little more but it is worth it to me. We
are on well water if that matters to you
-
By Jonathon On 2018-02-19 05:00:49
Fits my Kenmore just fine. Takes a bit of pressure to push it into the holes, but that means it's getting a good seal. This is my first one and they have never leaked. You do need to run some water through it after you install it to flush it out a bit.
How often should you replace your water filter?
- On average, most filters last 6 months or 300 gallons depending on your water quality and usage.
How do I turn off my filter light to reset?
- If the filter light will not reset after following specific instructions from your owner manual, contact your refrigerator manufacturer.
Do the gaskets (o-rings) on the filters need to be lubricated?
- Most water filters come with pre-lubricated O-rings
- If you are having trouble installing the filter, we have found that a small amount of vegetable oil applied to the O-ring will ease installation and removal of the filter.
I just installed my filter; do I need to run water through it before I drink the water? If so, how much?
- You should run 3 gallons of water through your filter in order to flush it and make sure that it is thoroughly wet. Do not run the 3 gallons continuously, instead run the water for a few minutes and stop in between. Get a gallon water container, and pour and refill 3 times!
Live Customer Support
Our hours of operation are Monday thru Friday from 8:00am to 6:00pm Eastern Time and our after hours sales team is available 24 hours a day, 7 days a week. Whether it’s placing an order or answering questions that may help in your purchasing decisions, our specialists are ready to assist you. You can also contact us via email.