Replacement Refrigerator Water Filter For:
Maytag 8212650
Filter Features
-
Filter Life: 6-Months
-
Filter Capacity: 200 Gallon
-
NSF Certified 42 & 53
-
Taste
-
Odor
-
Chlorine
-
Reduces 24 Contaminants Including Pharmaceuticals
-
Replacement Refrigerator Water Filter For:
8212650
2-Pack ($35.99)
Save:
$34.00
158 Review
Add To Cart
-
Replacement Refrigerator Water Filter For:
8212650
3-Pack ($52.99)
Save:
$47.00
231 Review
Add To Cart
-
Replacement Refrigerator Water Filter For:
8212650
4-Pack ($69.99)
Save:
$60.00
95 Review
Add To Cart
-
Replacement Refrigerator Water Filter For:
8212650
6-Pack ($102.99)
Save:
$27.00
69 Review
Add To Cart
Remove unhealthy contaminants and any haziness efficiently from your drinking water with maytag 8212650 at Clatterans which uses the highest quality activated carbon and certifies to IAPMO, NSF/ANSI water treatment standards 42 for trapping and reducing detrimental impurities to reach the best water filtration results. We have numerous maytag refrigerator filter replacements to fit perfectly in your fridge. Fitermodel is an acceptable substitute without compromise on quality and flow to provide wholesome sweet water for your whole family. Drink safe water and taste clean ice from Clatterans filters.
Fits The Following Series
45429 Series |
45433 Series |
58703 Series |
51103 Series |
51102 Series |
1.Press the eject button to release the filter from the base grille.
2.Pull the filter straight out.
3.Turn the cap counterclockwise to remove it from the filter.
IMPORTANT: Do not discard the cap. It is part of your
refrigerator. Keep the cap to use with the replacement filter.
4.Align the ridge on the cap with the arrow on the new filter and turn the cap until it snaps into place.
NOTE: You can run the dispenser without a filter. Your water will not be filtered. Simply insert the cap all of the way into the base grille and rotate the cap until it is firmly in place.
5.Remove the protective covers from the O-rings. Be sure the O-rings are still in place after the covers are removed.
6.Push the filter into the base grille. The eject button will pop back out when the filter is fully engaged.
7.Run water from the dispenser for 5 minutes at .5 gpm (about 2½ gallons) to clear the system and prevent sputtering.
NOTE: Initial rate may be slower than expected. Full rate should be restored within 24-36 hours
8.Reset the “replace filter” light, if needed, by holding the reset button for three seconds.
Top customer reviews
-
By Kim On 2018-02-11 06:09:52
Replaced my old PUR filter (W10193691) with this one and I have not noticed any
weird taste or smell in the water that other reviewer's have mentioned. Plus
it's half the price of the old filter!
-
By Lois On 2018-02-10 06:52:06
Fit our Kenmore perfectly with no leaks. No detectable decrease in water
pressure at dispenser. It seems to do a good job in filtering water as it
tastes much better than what comes out of faucet. It is a little pricey, but
you get what you pay for. Will probably buy again when time comes to change it
again.
-
By Lois On 2018-02-10 03:13:14
Our water tastes pretty great to begin with so that's probably why we didn't notice a difference between this new filter (whirlpool 4396841) and the previous model. I can't say if it helps bad water but I can say it doesn't take anything away from already good water. And I'm very picky with water since it's the only thing I drink other than tea and coffee.
-
By Carrie On 2018-02-09 11:04:12
I bought this to use with my Whirlpool fridge. It was easy to install. Per the packaging instructions, I ran 4 gallons of water through the filter before drinking. It sputtered a bit in the beginning but that is normal. The flow of the water is great and it tastes good to me! Will gladly purchase this product again and definitely recommend it to anyone looking for a water filter.
-
By Kristine On 2018-02-07 13:11:14
I used to use PUR W10177635, too expensive for me to shop on the original PUR shop, service is not so good. Now I tried this, does have a taste and I flushed 2 gallons through it. May depend on different preferences.
-
By Elena On 2018-02-07 06:14:45
We purchased this whirlpool filter 3 for our vacation home refrigerator after trying other
replacements. Delivery was fast and the product works better than expected.
The water tastes better! Highly recommend and we bought another for the next time we need a replacement !
How often should you replace your water filter?
- On average, most filters last 6 months or 300 gallons depending on your water quality and usage.
How do I turn off my filter light to reset?
- If the filter light will not reset after following specific instructions from your owner manual, contact your refrigerator manufacturer.
Do the gaskets (o-rings) on the filters need to be lubricated?
- Most water filters come with pre-lubricated O-rings
- If you are having trouble installing the filter, we have found that a small amount of vegetable oil applied to the O-ring will ease installation and removal of the filter.
I just installed my filter; do I need to run water through it before I drink the water? If so, how much?
- You should run 3 gallons of water through your filter in order to flush it and make sure that it is thoroughly wet. Do not run the 3 gallons continuously, instead run the water for a few minutes and stop in between. Get a gallon water container, and pour and refill 3 times!
Live Customer Support
Our hours of operation are Monday thru Friday from 8:00am to 6:00pm Eastern Time and our after hours sales team is available 24 hours a day, 7 days a week. Whether it’s placing an order or answering questions that may help in your purchasing decisions, our specialists are ready to assist you. You can also contact us via email.