Kenmore 70319
Fits The Following Models
Kenmore Refrigerator Models
-
70312
-
70313
-
70319
-
70342
-
70343
-
70349
-
70412
-
70413
-
70419
-
70423
-
70443
-
25370312211
-
25370312212
-
25370312213
-
25370343415
-
25370343416
-
25370343417
-
25370343418
-
25370343419
-
25370349210
-
25370349410
-
25370349411
-
25370349412
-
25370349413
-
25370349414
-
25370349415
-
25370349416
-
25370312214
-
25370313210
-
25370313211
-
25370313212
-
25370313213
-
25370313214
-
25370319211
-
25370319212
-
25370319213
-
25370319214
-
25370342210
-
25370342410
-
25370342411
-
25370342412
-
25370349417
-
25370349418
-
25370349419
-
25370412410
-
25370412411
-
25370412413
-
25370413410
-
25370413411
-
25370419410
-
25370419411
-
25370423410
-
25370423411
-
25370423419
-
25370342413
-
25370342414
-
25370342415
-
25370342416
-
25370342417
-
25370342418
-
25370342419
-
25370343210
-
25370343410
-
25370343411
-
25370343412
-
25370343413
-
25370343414
-
25370443210
-
25370443410
-
25370443411
-
25370443412
-
25370443413
-
25370443419
-
2537034241D
-
2537034341D
-
2537034941D
-
2537041241B
-
2537041341B
-
2537041941B
-
2537042341A
1.Turn Off the ice maker and remove the filter by pushing on the end/face of the filter.
2.Slide the old water filter cartridge straight out of the housing and discard it.
3.Unpackage the new filter cartridge. Using the alignment guide, slide it gently into the filter housing until it stops against the snap-in connector at the back of the housing.
4.Turn the filter clockwise until it locks into the housing.
NOTE: If the filter is not correctly locked into the housing, the water dispenser will not operate.
Water will not flow from the dispenser.
5.Push firmly until the cartridge snaps into place
(you should hear a click as the cartridge engages the snap-in connector).
6.Run water from the dispenser for 5 minutes at.5 gpm (about 2½ gallons) to clear the system and prevent sputtering.
NOTE: Initial rate may be slower than expected. Full rate should be restored within 24-36 hours
7.Reset the “replace filter" light, if needed, by holding the reset button for three seconds.
Top customer reviews
-
By Dorothy On 2018-07-12 09:10:29
So far, so good! Was easy to uninstall the old one and reinstall the new one. Had fresh filtered water again in a matter of minutes! Also, I was contacted by the seller and they seemed very helpful & friendly. We'll definitely be using GE MWF water filter from Clatterans again!
-
By Ronnie On 2018-07-04 10:43:06
A cheaper MWF filter alternative that gives the same results as the more expensive brands. Easy to install.
-
By Fernando On 2018-04-26 06:10:31
I had never changed the Kenmore filter on my refrigerator before and was nervous to start. If you can install a light bulb, you can swap this filter. Extremely easy and worth it if you like clean water. Faster shipping will be better.
-
By Gwen On 2018-04-21 09:22:54
Totally same top configuration and less time to screw on to replace the original one, run 4 gallons water after installation as the original instructions suggested to clear all taste and I am satisfied with this Kenmore 9991. But the shipping is not fast enough for me.
-
By Loren On 2018-04-14 06:50:10
Received the filters super quick and installed one last night. This was the first time I had replaced a filter in this fridge since I purchased it, so the directions included were very helpful. Will order again when the auto sensor of my fridge tells me to change the filter.
-
By Willie On 2018-04-10 02:45:25
Like other reviewers, paying much lower for a GE filter was getting old! This filter fits perfectly, works great and less than the price of the old one. This is my second purchase of this product and I'll keep buying them as long as they keep making them.
How often should you replace your water filter?
- On average, most filters last 6 months or 300 gallons depending on your water quality and usage.
How do I turn off my filter light to reset?
- If the filter light will not reset after following specific instructions from your owner manual, contact your refrigerator manufacturer.
Do the gaskets (o-rings) on the filters need to be lubricated?
- Most water filters come with pre-lubricated O-rings
- If you are having trouble installing the filter, we have found that a small amount of vegetable oil applied to the O-ring will ease installation and removal of the filter.
I just installed my filter; do I need to run water through it before I drink the water? If so, how much?
- You should run 3 gallons of water through your filter in order to flush it and make sure that it is thoroughly wet. Do not run the 3 gallons continuously, instead run the water for a few minutes and stop in between. Get a gallon water container, and pour and refill 3 times!
Live Customer Support
Our hours of operation are Monday thru Friday from 8:00am to 6:00pm Eastern Time and our after hours sales team is available 24 hours a day, 7 days a week. Whether it’s placing an order or answering questions that may help in your purchasing decisions, our specialists are ready to assist you. You can also contact us via email.