Maytag MFT2776DEE
Fits The Following Models
Maytag Refrigerator Models
-
MFT2574DEE
-
MFT2776DEM
-
MFT2574DEH
-
MFT2574DEM
-
MFT2776DEE
-
MFT2776DEH
1.Locate the accessory packet in the refrigerator and remove the water filter.
2.Take the water filter out of its packaging and remove the cover from the 0-rings. Be sure the 0-rings are still in place after the cover is removed.
NOTE: There may be some water in the filter. Some spilling may occur. Use atowel to wipe up any spills.
3.Align the arrow on the water filter label with the cutout notch in the filter housing and insert the filter into the housing.
4.Turn the filter clockwise until it locks into the housing.
NOTE: If the filter is not correctly locked into the housing, the water dispenser will not operate. Water will not flow from the dispenser.
5.While the compartment door is still open, lift the filter up into the compartment. Then, close the filter compartment door completely.
6.Run water from the dispenser for 5 minutes at .5 gpm(about 2.5 gallons) to clear the system and prevent sputtering.
NOTE: Initial rate may be slower than expected. Full rate should be restored within 24-36 hours.
7.Reset the "replace filter" light, if needed, by holding the reset button for three seconds.
Top customer reviews
-
By Wilson On 2019-10-23 05:40:14
You must run the water to dispense at least a couple of galloons to get rid of the cloudiness that many reviewers are referring to. Once he cloudiness is gone, the filter is ready to go. I did notice better drinking water quality. Depending on how much water is dispensed, this filter should last up to 6 months. It is easy to install but the price is steep.
-
By Mathew On 2019-10-20 15:16:16
Fit my fridge like it said it would, and relatively easy to swap out.
-
By Christian On 2019-10-18 11:17:17
Makes our water taste great, and I love that I didn't have to go to Wal-Mart to purchase this!
-
By Eula On 2019-10-18 10:12:19
Easy to install & what a difference in the water. We have hard water, therefore we have to use a water softener. The water tastes cleaner, crisper & no salty taste. We bought alot of gallons of Spring Water, no more. It is nice to fill up my water bottle with cold, fresh water from the fridge.
-
By Claire On 2019-10-15 11:36:19
Easy to replace the refrigerator filter. This makes the water taste fine or better than if it was from the faucet.
-
By Katie On 2019-10-11 10:18:14
Fits perfect so far so good.
How often should you replace your water filter?
- On average, most filters last 6 months or 300 gallons depending on your water quality and usage.
How do I turn off my filter light to reset?
- If the filter light will not reset after following specific instructions from your owner manual, contact your refrigerator manufacturer.
Do the gaskets (o-rings) on the filters need to be lubricated?
- Most water filters come with pre-lubricated O-rings
- If you are having trouble installing the filter, we have found that a small amount of vegetable oil applied to the O-ring will ease installation and removal of the filter.
I just installed my filter; do I need to run water through it before I drink the water? If so, how much?
- You should run 3 gallons of water through your filter in order to flush it and make sure that it is thoroughly wet. Do not run the 3 gallons continuously, instead run the water for a few minutes and stop in between. Get a gallon water container, and pour and refill 3 times!
Live Customer Support
Our hours of operation are Monday thru Friday from 8:00am to 6:00pm Eastern Time and our after hours sales team is available 24 hours a day, 7 days a week. Whether it’s placing an order or answering questions that may help in your purchasing decisions, our specialists are ready to assist you. You can also contact us via email.