Maytag MFT2776DEE
Fits The Following Models
Maytag Refrigerator Models
-
MFT2574DEE
-
MFT2776DEM
-
MFT2574DEH
-
MFT2574DEM
-
MFT2776DEE
-
MFT2776DEH
1.Locate the accessory packet in the refrigerator and remove the water filter.
2.Take the water filter out of its packaging and remove the cover from the 0-rings. Be sure the 0-rings are still in place after the cover is removed.
NOTE: There may be some water in the filter. Some spilling may occur. Use atowel to wipe up any spills.
3.Align the arrow on the water filter label with the cutout notch in the filter housing and insert the filter into the housing.
4.Turn the filter clockwise until it locks into the housing.
NOTE: If the filter is not correctly locked into the housing, the water dispenser will not operate. Water will not flow from the dispenser.
5.While the compartment door is still open, lift the filter up into the compartment. Then, close the filter compartment door completely.
6.Run water from the dispenser for 5 minutes at .5 gpm(about 2.5 gallons) to clear the system and prevent sputtering.
NOTE: Initial rate may be slower than expected. Full rate should be restored within 24-36 hours.
7.Reset the "replace filter" light, if needed, by holding the reset button for three seconds.
Top customer reviews
-
By Casey On 2018-06-08 10:10:04
Did what it is supposed to do. Was easy to install and came when promised. Recommend the filter 2 to anyone who needs to buy a new one or replace the old one.
-
By Chris On 2018-06-07 08:42:03
I have to use this in my fridge model. It works. Wish they were cheaper!!!
-
By Angelina On 2018-06-03 02:27:05
The EDR2RXD1 works very well completely take the awful taste from our city water. Price is why it 4 stars.
-
By Nicolas On 2018-05-26 05:42:03
Although I do like this filter 2, a lot, it is somewhat pricey. And it is the only filter that will work correctly in my Whirlpool Refrigerator.
-
By Gordon On 2018-05-20 09:09:51
Now I get clean drinking water from my Whirlpool fridge after flushing according to the instructions.
-
By Lois On 2018-05-19 08:06:30
Had this before and now added to Subscribe and Save. Solid, reliable water filter. Will order the filter 2 again from Clatterans when it needs to replace the new one.
How often should you replace your water filter?
- On average, most filters last 6 months or 300 gallons depending on your water quality and usage.
How do I turn off my filter light to reset?
- If the filter light will not reset after following specific instructions from your owner manual, contact your refrigerator manufacturer.
Do the gaskets (o-rings) on the filters need to be lubricated?
- Most water filters come with pre-lubricated O-rings
- If you are having trouble installing the filter, we have found that a small amount of vegetable oil applied to the O-ring will ease installation and removal of the filter.
I just installed my filter; do I need to run water through it before I drink the water? If so, how much?
- You should run 3 gallons of water through your filter in order to flush it and make sure that it is thoroughly wet. Do not run the 3 gallons continuously, instead run the water for a few minutes and stop in between. Get a gallon water container, and pour and refill 3 times!
Live Customer Support
Our hours of operation are Monday thru Friday from 8:00am to 6:00pm Eastern Time and our after hours sales team is available 24 hours a day, 7 days a week. Whether it’s placing an order or answering questions that may help in your purchasing decisions, our specialists are ready to assist you. You can also contact us via email.